Akım ( Amper ) Ayarı / current setting
Set Amper, elektroliz ünitesine verilecek güç ayarı içindir. Out Amper solusyon yüzdesi yeterli olduğu zaman giriş amperi ile eşitlenir ve sistem sağlıklı çalışır. Güç artırmak için ( hava filtresine verilen gazın miktarının yükseltilmesi için ) ( + ) tuşuna basılır. Güç düşürmek için ( hava filtresine verilen gazın miktarının azaltılması için ) ( - ) tuşuna basılır.rnHer dokunuş 0.50 artma veya azalma sağlar. Mevcut ayarı saklamak için ( S ) tuşuna basılır. Ayar yapıldıktan sonra set tuşuna basılmadığı durumda araç kontak kapatana kadar yeni ayarda kalır, kontak kapatılıp tekrar çalıştığında eski haline döner
Set Amper is for setting the power to be given to the electrolysis unit. When the Out Ampere solution percentage is sufficient, it is synchronized with the input ampere and the system works properly. To increase the power (to increase the amount of gas supplied to the air filter) (+) button is pressed. Press the (-) key to decrease the power (to decrease the amount of gas supplied to the air filter) .rn Each touch provides 0.50 increase or decrease. Press the (S) button to save the current setting. If the set button is not pressed after the setting is made, the vehicle remains in the new setting until the ignition is turned off, it returns to its original state when the ignition is turned off and on again.
Set amper ile out amperden fazla ise / If the set is more than amperage and out ampere
Set amper Out amperden fazla ise istenilen gaz akışı yeterli seviyede sağlanamaz bu durumda aşağıda ki, hata mesajını alırsınız.
If the set ampere Out is more than amperes, the desired gas flow cannot be achieved at a sufficient level, in which case you will get the following error message
Solusyon yetersiz hata mesajı / Insufficient solution error message
Solusyon yoğunluğunun artırılması gerekir.
Solution density should be increased.
Set amper ile out amperden az ise / If the set is less than the out ampere with ampere
Set amper Out amperden az ise istenilen gaz akışı yeterli seviyede sağlanamaz bu durumda aşağıda ki, hata mesajını alırsınız.
If the set ampere Out is less than amperes, the desired gas flow cannot be achieved at a sufficient level, in this case, you will get the following error message.
Solusyon fazla hata mesajı / Solution too much error message
Bu durumda solusyon yoğunluğunun azaltılması gereklidir. Sistem pwm i ve elekroliz cihazını korumak amacı ile istenilen seviyede solüsyon oranını otomatik hesaplar ve miktar fazla geldiğinde uyarı verir, solüsyonun mutlaka seyreltilmesi gereklidir.
In this case, it is necessary to reduce the solution density. The system automatically calculates the desired level of solution ratio in order to protect the pwm and the electrolysis device and gives a warning when the amount is too much, the solution must be diluted.
Solusyon ölçümü / Solution measurement
Elektroliz regülatörünün sağlıklı şartlarda çalışabilmesi ve performans için solusyon yüzdesinin tam değerlerde olması şarttır. Solusyon ekranı ile kontrolü sağlanır ve sistemin uzun ömürlü, sağlıklı çalışması sağlanır.
For the electrolysis regulator to work under healthy conditions and for performance, the percentage of solution must be at full values. It is controlled by the solution screen and the long-lasting and healthy operation of the system is ensured.
Sistemin tükettiği akım değerleri / The current values consumed by the system
Çekilen amper değerini, PWM üzerinde ki gerilim yükünü ve anlık tüketilen amperi gösterir.
It shows the ampere value drawn, the voltage load on the PWM and the instantaneous consumed amperage.
Elektrik akımı genel verileri / Electric current general data
Sistemin araçtan çektiği Watt, akü voltajı, çekilen amper
Watt drawn by the system from the vehicle, battery voltage, ampere drawn
Buzzer ses sinyal ayarı / Buzzer sound signal setting
Uyarı ikaz seslerini açma kapama
Turn on / off warning beeps
Sistem başlatma zaman ayarı / System start time setting
Sistemin devreye girme bekleme saniye ayarıdır. ( - ) ve ( + ) tuşlarına basılarak değer değiştirilebilir. Set tuşuna basarak girilen değer saklanır
It is the activation wait second setting of the system. The value can be changed by pressing the (-) and (+) keys. The entered value is stored by pressing the set button.
Toplam çalışma zamanı / Total uptime
Sistemin araç üzerindeki toplam çalışma saatini gösterir.
Total uptime
Kısa devre uyarısı / Short circuit warning
Öncelikle aşırı yoğun solusyon hazırlamadığına emin olun, öncelikle solüsyonu seyreltin. Solusyon yoğunluğu değilse, elektroliz regülatörüne bağlanan kablolarda, bağlantı ayaklarında, elektroliz ünitesindeki iç plakalara temas olup olmadığını kontrol ediniz.rnDikkat edilmesi gereken önemli durumlar.rnSolusyon hazırlanırken yeterli yoğunluk olduğu halde out amper set amperden düşük kalıyorsa, pwm kablolarını tamamen sökün, elektroliz regülatöründen gelen artı ve eksi kabloları ayırın, artı kabloyu akü artısına eksi kabloyu akü eksisine direkt bağlayın ve sistemi direkt çalıştırın. Belli sürelerde tekrar pwm bağlantılarını yaparak sistemin düzgün çalışıp çalışmadığını kontrol edin. rnSolusyon sıvısının seyreltilmesi gerektiğinde üzerine eklenen saf su ile cihaz içindeki yoğun solusyon hemen karışmayacağından bu durumda da elektroliz regülatörü direkt çalıştırılabilir. rnDİKKAT: rnElektroliz regülatörü direkt bağlama ve çalıştırma bayilerimiz tarafından yapılır, kullanıcılarımızın yapmaması sistem ve araç sağlığı açısından önemlidir.
Short circuit warning